Enhancing the Tensile Properties and Ductile-Brittle Transition Behavior of the EN S355 Grade Rolled Steel via Cost-Saving Processing Routes.

Structural rolled steels are the primary products of modern ferrous metallurgy. Consequently, enhancing the mechanical properties of rolled steel using energy-saving processing routes without furnace heating for additional heat treatment is advisable. This study compared the effect on the mechanical properties of structural steel for different processing routes, like conventional hot rolling, normalizing rolling, thermo-mechanically controlled processing (TMCP), and TMCP with accelerating cooling (AC) to 550 °C or 460 °C. The material studied was a 20 mm-thick sheet of S355N grade (EN 10025) made of low-carbon (V+Nb+Al)-micro-alloyed steel. The research methodology included standard mechanical testing and microstructure characterization using optical microscopy, scanning and transmission electronic microscopies, energy dispersive X-ray spectrometry, and X-ray diffraction. It was found that using different processing routes could increase the mechanical properties of the steel sheets from S355N to S550QL1 grade without additional heat treatment costs. TMCP followed by AC to 550 °C ensured the best combination of strength and cold-temperature resistance due to formation of a quasi-polygonal/acicular ferrite structure with minor fractions of dispersed pearlite and martensite/austenite islands. The contribution of different structural factors to the yield tensile strength and ductile-brittle transition temperature of steel was analyzed using theoretical calculations. The calculated results complied well with the experimental data. The effectiveness of the cost-saving processing routes which may bring definite economic benefits is concluded.

Effect of Rare Earth Elements on Microstructure and Tensile Behavior of Nb-Containing Microalloyed Steels.

The present investigation endeavors to explore the influence of rare earth elements on the strength and plasticity characteristics of low-carbon microalloyed steel under tensile loading conditions. The findings from the conducted tensile tests indicate that the incorporation of rare earths leads to a notable enhancement in the yield strength, ultimate tensile strength, and ductility properties of the steel. A comparative analysis of the microstructures reveals that the presence of rare earths significantly refines and optimizes the microstructure of the microalloyed steel. This optimization is manifested through a reduction in grain size, diminution of inclusion sizes, and a concomitant rise in their number density. Moreover, the addition of rare earths is observed to foster an increase in the volumetric fraction of carbides within the steel matrix. These multifaceted microstructural alterations collectively contribute to a substantial strengthening of the microalloyed steel. Furthermore, it is elucidated that the synergistic interaction between rare earth elements and both carbon (C) and niobium (Nb) in the steel matrix augments the extent of the Lüders strain region during the tensile deformation of specimens. This phenomenon is accompanied by the effective modification of inclusions by the rare earths, which serves to mitigate stress concentrations at the interfaces between the inclusions and the surrounding matrix. This article systematically evaluates the modification mechanism of rare earth microalloying, which provides a basis for broadening the application of rare earth microalloying in microalloyed steel.

MH-STRALP: A scoring system for prognostication in patients with upper gastrointestinal bleeding.

BACKGROUND: Upper gastrointestinal bleeding (UGIB) is a common medical emergency and early assessment of its outcomes is vital for treatment decisions. AIM: To develop a new scoring system to predict its prognosis. METHODS: In this retrospective study, 692 patients with UGIB were enrolled from two centers and divided into a training (n = 591) and a validation cohort (n = 101). The clinical data were collected to develop new prognostic prediction models. The endpoint was compound outcome defined as (1) demand for emergency surgery or vascular intervention, (2) being transferred to the intensive care unit, or (3) death during hospitalization. The models' predictive ability was compared with previously established scores by receiver operating characteristic (ROC) curves. RESULTS: Totally 22.2% (131/591) patients in the training cohort and 22.8% (23/101) in the validation cohort presented poor outcomes. Based on the stepwise-forward Logistic regression analysis, eight predictors were integrated to determine a new post-endoscopic prognostic scoring system (MH-STRALP); a nomogram was determined to present the model. Compared with the previous scores (GBS, Rockall, ABC, AIMS65, and PNED score), MH-STRALP showed the best prognostic prediction ability with area under the ROC curves (AUROCs) of 0.899 and 0.826 in the training and validation cohorts, respectively. According to the calibration curve, decision curve analysis, and internal cross-validation, the nomogram showed good calibration ability and net clinical benefit in both cohorts. After removing the endoscopic indicators, the pre-endoscopic model (pre-MH-STRALP score) was conducted. Similarly, the pre-MH-STRALP score showed better predictive value (AUROCs of 0.868 and 0.767 in the training and validation cohorts, respectively) than the other pre-endoscopic scores. CONCLUSION: The MH-STRALP score and pre-MH-STRALP score are simple, convenient, and accurate tools for prognosis prediction of UGIB, and may be applied for early decision on its management strategies.

The association between serum copper concentration and prevalence of diabetes among US adults with hypertension (NHANES 2011-2016).

The objective of this study was to examine the association between the serum copper concentration and the prevalence of diabetes among US adults with hypertension using the data from the National Health and Nutrition Examination Survey (NHANES). The study population was selected from adults aged over 20 years old in the three survey cycles of NHANES from 2011 to 2016. Logistic regression model analyses were applied to determine the independent risky effect of copper to the prevalence of diabetes. Also, a restricted cubic spline (RCS) model was performed to explore the potential nonlinear association between serum copper concentration and the prevalence of diabetes. A total of 1786 subjects (742 cases and 1044 controls) were included, and 924 were men (51.7%), and 742 (41.5%) were diabetic. Compared with non-diabetic individuals, the concentration of serum copper in diabetic patients with hypertension was higher. After adjusting for age, sex, race, education, marital status, body mass index (BMI), family poverty income ratio (PIR), smoking, alcohol drinking, physical activity, systolic blood pressure (SBP), diastolic blood pressure (DBP), and hyperlipidemia, the highest quartile of serum copper concentration significantly increased the risk of diabetes as compared with the lowest quartile (OR: 1.38, 95% CI: 1.01-1.92, ptrend = 0.036). The results of RCS analysis showed significant non-linear relationship between serum copper concentration and prevalence of diabetes (p-non-linear = 0.010). This study finds that serum copper concentration are significantly associated with risk of diabetes in hypertensive patients, which suggests copper as an important risk factor of diabetes development.

The Performance of Niobium-Microalloying Ultra-High-Strength Bridge Cable Steel during Hot Rolling.

This study focuses on exploring the effects of niobium (Nb)-microalloying on the properties of steel for ultra-high-strength bridge cables during hot-rolling processes. We employed a combination of dual-pass compression tests, stress-strain curve analysis, and Electron Backscatter Diffraction (EBSD) techniques to investigate the influence of Nb-microalloying on the static recrystallization behavior and grain size of the steel. The key findings reveal that Nb-microalloying effectively inhibits static recrystallization, particularly at higher temperatures, significantly reducing the volume fraction of recrystallized grains, resulting in a finer grain size and enhanced deformation resistance. Secondly, at a deformation temperature of 975 °C, Nb-containing steel exhibited finer grain sizes compared to Nb-free steel when held for 10 to 50 s; however, the grain size growth accelerated when the hold time exceeded 50 s, likely linked to the increased deformation resistance induced by Nb. Lastly, this research proposes optimal hot-rolling process parameters for new bridge cable steel, recommending specific finishing rolling temperatures and inter-pass times for both Nb-containing and Nb-free steels during the roughing and finishing stages. This study suggests optimal hot-rolling parameters for both Nb-containing and Nb-free steels, providing essential insights for improving hot-rolling and microalloying processes in high-carbon steels for bridge cables.

Phase Transformation Temperature Prediction in Steels via Machine Learning.

The phase transformation temperature plays an important role in the design, production and heat treatment process of steels. In the present work, an improved version of the gradient-boosting method LightGBM has been utilized to study the influencing factors of the four phase transformation temperatures, namely Ac1, Ac3, the martensite transformation start (MS) temperature and the bainitic transformation start (BS) temperature. The effects of the alloying element were discussed in detail by comparing their influencing mechanisms on different phase transformation temperatures. The training accuracy was significantly improved by further introducing appropriate features related to atomic parameters. The melting temperature and coefficient of linear thermal expansion of the pure metals corresponding to the alloying elements, atomic Waber-Cromer pseudopotential radii and valence electron number were the top four among the eighteen atomic parameters used to improve the trained model performance. The training and prediction processes were analyzed using a partial dependence plot (PDP) and Shapley additive explanation (SHAP) methods to reveal the relationships between the features and phase transformation temperature.

The feedback loop of EFTUD2/c-MYC impedes chemotherapeutic efficacy by enhancing EFTUD2 transcription and stabilizing c-MYC protein in colorectal cancer.

BACKGROUND: Chemoresistance presents a significant obstacle in the treatment of colorectal cancer (CRC), yet the molecular basis underlying CRC chemoresistance remains poorly understood, impeding the development of new therapeutic interventions. Elongation factor Tu GTP binding domain containing 2 (EFTUD2) has emerged as a potential oncogenic factor implicated in various cancer types, where it fosters tumor growth and survival. However, its specific role in modulating the sensitivity of CRC cells to chemotherapy is still unclear. METHODS: Public dataset analysis and in-house sample validation were conducted to assess the expression of EFTUD2 in 5-fluorouracil (5-FU) chemotherapy-resistant CRC cells and the potential of EFTUD2 as a prognostic indicator for CRC. Experiments both in vitro, including MTT assay, EdU cell proliferation assay, TUNEL assay, and clone formation assay and in vivo, using cell-derived xenograft models, were performed to elucidate the function of EFTUD2 in sensitivity of CRC cells to 5-FU treatment. The molecular mechanism on the reciprocal regulation between EFTUD2 and the oncogenic transcription factor c-MYC was investigated through molecular docking, ubiquitination assay, chromatin immunoprecipitation (ChIP), dual luciferase reporter assay, and co-immunoprecipitation (Co-IP). RESULTS: We found that EFTUD2 expression was positively correlated with 5-FU resistance, higher pathological grade, and poor prognosis in CRC patients. We also demonstrated both in vitro and in vivo that knockdown of EFTUD2 sensitized CRC cells to 5-FU treatment, whereas overexpression of EFTUD2 impaired such sensitivity. Mechanistically, we uncovered that EFTUD2 physically interacted with and stabilized c-MYC protein by preventing its ubiquitin-mediated proteasomal degradation. Intriguingly, we found that c-MYC directly bound to the promoter region of EFTUD2 gene, activating its transcription. Leveraging rescue experiments, we further confirmed that the effect of EFTUD2 on 5-FU resistance was dependent on c-MYC stabilization. CONCLUSION: Our findings revealed a positive feedback loop involving an EFTUD2/c-MYC axis that hampers the efficacy of 5-FU chemotherapy in CRC cells by increasing EFTUD2 transcription and stabilizing c-MYC oncoprotein. This study highlights the potential of EFTUD2 as a promising therapeutic target to surmount chemotherapy resistance in CRC patients.

Preparation, Characterization, and Magnetic Resonance Imaging of Mn@SiO2 Nanowires.

The deposition time was controlled to prepare Mn nanowires of different lengths and diameters on templates of anodic aluminum oxide (AAO) with different pore sizes. The surface of as-prepared Mn nanowires was modified with SiO2 using the sol-gel method to improve their dispersion in aqueous solution. The effects of the diameter and length of the as-prepared Mn nanowires coated with SiO2 on the relaxivity were investigated. It was found that the Mn@SiO2 nanowires have smaller diameters and a higher longitudinal relaxivity (r1) with an increased length. Mn3@SiO2 nanowires had the highest r1 value of 5.8 mM-1 s-1 among the Mn@SiO2 nanowires (Mn3 nanowires have a diameter of about 30 nm and a length of about 0.5 µm length). Additionally, the biocompatibility and in vivo imaging ability of the Mn3@SiO2 nanowires were evaluated. The Mn3@SiO2 nanowires had good cytotoxicity and biocompatibility, and the kidney of SD rats showed a positive enhancement effect during small animal imaging at 1.5 T. This study showed that the Mn3@SiO2 nanowires could potentially become contrast agents (CAs) of longitudinal relaxation time (T1).

Preparation, characterization, and magnetic resonance imaging of Fe nanowires.

A facile template method was employed to synthesize Fe nanowires of different sizes, dimensions. Comprehensive analyses were conducted to explore their morphology, structure, composition, and magnetic properties. The surface of as-prepared Fe nanowires was modified with SiO2 by sol-gel method to improve the dispersion of as-prepared Fe nanowires in aqueous solution. Furthermore, the relaxation properties, biocompatibility and in vivo imaging abilities of the Fe@SiO2 nanowires were evaluated. The study revealed that the SiO2-coated Fe nanowires functioned effectively as transverse relaxation time (T2) contrast agents (CAs). Notably, as the length of the Fe@SiO2 nanowires increased, their diameter decreased, leading to a higher the transverse relaxivity (r2) value. Our study identified that among the Fe nanowires synthesized, the Fe3@SiO2 nanowires, characterized by a diameter of around 30 nm and a length of approximately 500 nm, exhibited the highest r2 value of 59.3 mM-1 s-1. These nanowires demonstrated good biocompatibility and non-toxicity. Notably, upon conducting small animal imaging a 1.5 T with Sprague-Dawley rats, we observed a discernible negative enhancement effect in the liver. These findings indicate the promising potential of Fe@SiO2 nanowires as T2 CAs, with the possibility of tuning their size for optimized results.

Effect of Austempering Processes on the Tensile Properties and the Work-Hardening Behavior of Austempered Bainitic Steels Below the Martensite Start Temperature.

The tensile properties and work-hardening behavior of austempered bainitic steels below martensite start temperature (Ms) were investigated and compared with those of bainitic steel austempered above Ms. The results show that the tensile strength and yield strength increased from 1096 MPa and 734 MPa to 1203 MPa and 951 MPa, respectively, when the austempering temperature was decreased from 400 °C to 300 °C. However, the total elongation decreased from 23% to 16%. The martensite-retained austenite blocks and bainitic ferrite laths are significantly refined. With a decrease in the austempering temperature, the volume fraction of retained austenite decreased from 15.4 vol% to 6.2 vol%. The carbon content in retained austenite increased from 1.12 wt% to 1.69 wt%. All tensile specimens exhibited three stages of deformation in the differential Crussard-Jaoul (C-J) models. The difference in ductility is mainly attributed to the transformation of the retained austenite blocks into strain-induced martensite during deformation. The initial content of retained austenite is the main factor affecting the ductility of bainitic steels. Therefore, the work-hardening ability of austempered bainitic steel above Ms is higher than that of bainitic steel below Ms.

Spin-orbit splitting and piezoelectric properties of Janus Ge2XY (X ≠ Y = P, As, Sb and Bi).

The coexistence of spin-orbit coupling and piezoelectricity in a single material may have potential application in multifunctional devices, including spintronics, nanorobotics and piezotronics. Spin-orbit coupling provides a new means to manipulate electron's spin without an additional external magnetic field, while piezoelectricity refers to the interplay between mechanical stresses and electric polarization. Using first-principles calculations, the structural, electronic, optical, spin, and piezoelectric properties of the Janus Ge2XY (X ≠ Y = P, As, Sb, and Bi) monolayers were systematically investigated. All the Ge2XY are energetically and dynamically stable in the α phase. At the GW level, Ge2AsSb, Ge2AsBi, and Ge2SbBi have direct fundamental band gaps of 0.65, 0.64, and 0.91 eV. At the GW + BSE level, their optical gaps are 0.42, 0.45, and 0.63 eV, and the optical absorption coefficients can reach about 10-5 cm-1 in the infrared light region, which reveals that they have potential for application in infrared photodetectors. For Ge2PBi, Ge2AsBi, and Ge2SbBi containing the heavy Bi element, the lowermost conduction band and uppermost valence band have large spin splitting along the M-K and K-Γ lines, and the bands near the Fermi level possess Rashba spin splitting at the Γ point. Ge2PBi and Ge2SbBi have both large in-plane piezoelectric coefficients d11 (-0.75 and -3.18 pm V-1) and out-of-plane piezoelectric coefficients d31 (0.37 and 0.30 pm V-1). Our findings are helpful to understand the mechanism of the spin-orbit physics and piezoelectricity of Janus Ge2XY monolayers and guide experiments in exploring novel multifunctional materials.

High-Entropy Spinel Ferrites with Broadband Wave Absorption Synthesized by Simple Solid-Phase Reaction.

In this work, high-entropy (HE) spinel ferrites of (FeCoNiCrM)xOy (M = Zn, Cu, and Mn) (named as HEO-Zn, HEO-Cu, and HEO-Mn, respectively) were synthesized by a simple solid-phase reaction. The as-prepared ferrite powders possess a uniform distribution of chemical components and homogeneous three-dimensional (3D) porous structures, which have a pore size ranging from tens to hundreds of nanometers. All three HE spinel ferrites exhibited ultrahigh structural thermostability at high temperatures even up to 800 °C. What is more, these spinel ferrites showed considerable minimum reflection loss (RLmin) and significantly enhanced effective absorption bandwidth (EAB). The RLmin and EAB values of HEO-Zn and HEO-Mn are about -27.8 dB at 15.7 GHz, 6.8 GHz, and -25.5 dB at 12.9 GHz, 6.9 GHz, with the matched thickness of 8.6 and 9.8 mm, respectively. Especially, the RLmin of HEO-Cu is -27.3 dB at 13.3 GHz with a matched thickness of 9.1 mm, and the EAB reaches about 7.5 GHz (10.5-18.0 GHz), which covers almost the whole X-band range. The superior absorbing properties are mainly attributed to the dielectric energy loss involving interface polarization and dipolar polarization, the magnetic energy loss referring to eddy current and natural resonance loss, and the specific functions of 3D porous structure, indicating a potential application prospect of the HE spinel ferrites as EM absorbing materials.

Application Research on Nb Microalloying of High-Carbon Pearlite Bridge Cable Wire Rods.

The application of Nb microalloying to high-carbon pearlite bridge cable wire rod steel has always been controversial, especially in the actual production process, which will be affected by the cooling rate, holding temperature and final bonding temperature. In this paper, the experimental characterization, finite element simulation and phase diagram calculation of the test steel were carried out, then the microstructure and properties of different parts of Nb microalloying of bridge cable wire rods were compared and analyzed. The phase transition interval of pearlite during the water-cooling process of bridge cable wire rods is increased due to the refinement of austenite grains, and the significant increase in the end temperature of the phase transition makes the average interlamellar spacing of pearlite increase. The cooling rate of different parts of bridge cable wire rods simulated by Abaqus has little difference. At the same time, Nb microalloying effectively increases the proportion of low-angle grain boundaries, so that the overall average misorientation representing the surface defects is reduced. This helps to reduce the surface energy and increase the stability of the microstructure. Combined with the mechanical properties of microtensile rods, it is found that the grain refinement effect of Nb is greater than that of coarsening interlamellar spacing during hot rolling deformation in actual production, which makes the tensile strength at the 1/4 section increase significantly. The overall tensile strength and area shrinkage of the steel wire have also been effectively improved.

Effects of Laser Cutting Parameters on the Magnetic Properties of 50W350 High-Grade Non-Oriented Electrical Steel.

Based on the application demand of laser cutting technology in non-oriented electrical steel, the influencing mechanisms of laser cutting parameters on the magnetic properties of 50W350 high-grade non-oriented electrical steel were investigated in this work. The specific total loss was utilized to evaluate the quality of cutting methods and the cutting parameter combinations. The results showed that the deterioration of the specific total loss was mainly due to the increase in hysteresis loss. Compared to traditional mechanic shearing, laser cutting generally degrades the magnetic properties under the evaluation index ΔP1.0/50. However, in some cases, laser cutting is superior to the mechanic shearing method under the evaluation index ΔP1.5/50. The main parameters related to laser cutting exhibited complicated influencing mechanisms on the specific total loss of 50W350 high-grade non-oriented electrical steel. However, based on the results of the experiments designed using the Box-Behnken model, the laser cutting parameters were optimized and the evaluation indexes have been significantly improved.

Study on the Single Sheet Measurement Method for AC Magnetic Measurement on Grain-Oriented Electrical Steel.

To quickly and accurately measure the AC magnetic properties of grain-oriented electrical steel by means of the existing measuring system designed for the magnetizing current method (MC), specifically the SST (92) single sheet method, in this work, the H-coil (HC) measuring system, which directly senses the magnetic field strength of the tested sample, was designed to measure the AC magnetic properties of the grain-oriented electrical steel. The assumed effective magnetic path length introduced in the MC method was corrected by comparing the measurement results obtained by means of HC and MC methods. The results found that specific total loss measured by the HC method was significantly lower than that measured by the classical magnetizing current (MC) method. Taking the HC method as the reference, the influencing factors of the effective magnetic path length was studied. It was found that the actual effective magnetic path length depends on the investigated sample characteristics, the measurement conditions, as well as yoke characteristics. The actual effective magnetic path length introduced in the MC method is examined to be more than 450 mm, fluctuating around 468 mm.

Local Corrosion Behaviors in the Coarse-Grained Heat-Affected Zone in a Newly Developed Zr-Ti-Al-RE Deoxidized High-Strength Low-Alloy Steel.

Oxide metallurgy technology can improve the microstructure of a coarse-grained heat-affected zone (CGHAZ) but introduces extra inclusions. Local corrosion behavior of the CGHAZ of a Zr-Ti-Al-RE deoxidized steel was investigated in this work using theoretical calculations and experimental verification. The modified inclusions have a (Zr-Mg-Al-Ca-RE)Ox core claded by a CaS and TiN shell. CaS dissolves first, followed by the oxide core, leaving TiN parts. This confirms that the addition of rare earth can reduce lattice distortion and prevent a galvanic couple between the inclusions and the matrix, while the chemical dissolution of CaS causes localized acidification, resulting in the pitting corrosion initiation.

Effects of highland barley ß-glucan on blood glucose and gut microbiota in streptozotocin-induced, diabetic, C57BL/6 mice on a high-fat diet.

OBJECTIVES: This study aimed to investigate the hypoglycemic effect of highland barley ß-glucan (HBG) on mice with type 2 diabetes (T2D), and determine whether the hypoglycemic effects are related to modulations of the gut microbiota. METHODS: T2D was induced with a high-fat diet and streptozotocin in the mice. HBG was orally administered to mice with T2D for 4 wk, and biochemical indices were analyzed in the serum and liver. Fecal samples were collected and analyzed with high-throughput 16S ribosomal RNA sequencing. RESULTS: Intake of HBG for 4 wk suppressed the body weight, as well as liver and heart indices, and regulated the levels of fasting blood glucose, serum insulin, blood lipid, oxidative damage, and inflammatory reaction in mice with T2D. Furthermore, HBG reversed the gut microbiota dysbiosis in mice with T2D by increasing the abundance of Lachnospiraceae_UCG-006, Streptococcaceae, and Eggerthellaceae, and by decreasing the abundance of Parasutterella. CONCLUSIONS: Our findings indicate that the antidiabetic abilities of HBG might be related to the improvement of gut microbiota imbalance.

Effects of Mn-Depleted Zone Formation on Acicular Ferrite Transformation in Weld Metals under High Heat Input Welding.

In this present work, during high heat input welding of the weld metal, different types of Mn-depleted zones were achieved by different cooling rates. The effects of cooling rates on Mn-depleted zone formation and acicular ferrite (AF) transformation were analyzed. The Mn-depleted zone around the inclusions, as well as the interface concentration of Mn atoms, are found to be significantly different with different cooling rates. When the cooling rate is 10 °C/s, the interface concentration of Mn atoms around the inclusions is the lowest, the area of Mn-depleted zone is the smallest, and the proportion of AF in the weld metal is the highest. As the cooling rate decreases further, the interface concentration of Mn begins to rise, the area of the Mn-depleted zone gradually expands, and the proportion of AF decreases. However, when the cooling rate reaches 100 °C/s, only a very small amount of MnS precipitates, no Mn-depleted zone forms around the inclusions, and acicular ferrite cannot be produced effectively in the weld metal.

Signaling pathways and therapeutic interventions in gastric cancer.

Gastric cancer (GC) ranks fifth in global cancer diagnosis and fourth in cancer-related death. Despite tremendous progress in diagnosis and therapeutic strategies and significant improvements in patient survival, the low malignancy stage is relatively asymptomatic and many GC cases are diagnosed at advanced stages, which leads to unsatisfactory prognosis and high recurrence rates. With the recent advances in genome analysis, biomarkers have been identified that have clinical importance for GC diagnosis, treatment, and prognosis. Modern molecular classifications have uncovered the vital roles that signaling pathways, including EGFR/HER2, p53, PI3K, immune checkpoint pathways, and cell adhesion signaling molecules, play in GC tumorigenesis, progression, metastasis, and therapeutic responsiveness. These biomarkers and molecular classifications open the way for more precise diagnoses and treatments for GC patients. Nevertheless, the relative significance, temporal activation, interaction with GC risk factors, and crosstalk between these signaling pathways in GC are not well understood. Here, we review the regulatory roles of signaling pathways in GC potential biomarkers, and therapeutic targets with an emphasis on recent discoveries. Current therapies, including signaling-based and immunotherapies exploited in the past decade, and the development of treatment for GC, particularly the challenges in developing precision medications, are discussed. These advances provide a direction for the integration of clinical, molecular, and genomic profiles to improve GC diagnosis and treatments.

Nanomechanics of Retained Austenite in Medium-Carbon Low-Temperature Bainitic Steel: A Critical Analysis of a One-Step versus a Two-Step Treatment.

A two-step bainitic treatment with a final isothermal temperature below MS was adopted to obtain bainitic steel with abundant retained austenite (RA). Nanoindentation testing was used to investigate the stability of RA in bainite steel and clarify the effect of RA on the deformation of medium-carbon steel. The results showed that, in contrast to the traditional one-step approach, a greater amount of nanoscale RA film was obtained using the two-step treatment. This was due to a lower final bainitic transformation temperature, which induced a higher carbon concentration in the untransformed austenite in the stasis stage; this resulted in untransformed austenite with a higher carbon content existing as RA rather than forming martensite in the subsequent cooling process. In addition, it was determined that the increased stability of RA during the two-step transformation delayed the pop-in point.